Effects of heat treatment temperature on the microstricuture and some mechanical properties of C36000 BRASS = Efeitos da temperatura de tratamento térmico na microestrutura e algumas propriedades mecãnicas do latão C36000

Abstract: This study aims to evaluate the influence of different annealing temperatures on the microstructure and mechanical behaviour of C36000 brass. The specimens were heat treated at temperatures ranging from 250°C to 850°C for 1 hour, followed by quenching in water. Afterward, the microstructural and mechanical characterization was performed. The Leia mais…

polimero

Próteses do futuro

Dois laboratórios do IPT participam de projeto em parceria para o desenvolvimento de tecnologias protéticas e ortopédicas utilizando materiais poliméricos e compósitos O desenvolvimento de tecnologias protéticas e ortopédicas por meio de materiais poliméricos e compósitos é o objetivo do projeto PdComp, coordenado pelo Instituto de Pesquisas Tecnológicas (IPT) e Leia mais…

Propriedades e aspectos do concreto aparente do patrimônio da arquitetura moderna brasileira

Resumo: O objetivo do estudo é investigar propriedades e aspectos do concreto aparente das empenas do edifício Vilanova Artigas e correlacioná-los ao estado de conservação, visando oferecer subsídios para preservação. O edifício completou 50 anos em 2019 e foi submetido a reparos estruturais recentemente (2013-2015). Ensaios laboratoriais e observações “in Leia mais…

Impact on pollution emissions of the flow measurement uncertainties in real drive enission meters

Abstract: Vehicle emissions have received a lot of attention in recent years due to their impact on climate change and air quality in large cities. As a result, efforts have been directed towards reducing vehicle pollutant emissions by regulating them, updating existing standards, and implementing technological improvements in the equipment Leia mais…

Numerical simulation and image analysis of a moltem metal atomization focused on the additive manufacturing route

Referência: ZERWAS, Alexandre Ariyoshi; SILVA, Flavia Costa da; FRITSCHING, Udo; PAIVA, Jose Luis de; GUARDANI, Roberto.  Numerical simulation and image analysis of a moltem metal atomization focused on the additive manufacturing route. In: CONGRESSO BRASILEIRO EM ENGENHARIA DE SISTEMAS EM PROCESSOS, 3., 2024, São Paulo. Pôster…  1 slides. Acesso aos Leia mais…

Multiscale two-dimensional multiparticle reactor model for non-catalytic gas-solid reactions

Referência: METOLINA, Patricia; SILVA, André Luiz Nunis da; GUARDANI, Roberto. Multiscale two-dimensional multiparticle reactor model for non-catalytic gas-solid reactions. In: CONGRESSO BRASILEIRO EM ENGENHARIA DE SISTEMAS EM PROCESSOS, 3., 2024, São Paulo. Pôster e Resumo… 2p. Acesso aos slides da apresentação da Palestra em PDF: https://escriba.ipt.br/pdf/179088.pdf

Piezoelectric energy harvesting from VIV on cantilevered flexible cylinders with orthotropic bending stiffiness: experimental investigation of varying flow effects

Abstract: This study presents experimental tests of VIV over an orthotropically stiffened cantilevered cylinder, equipped with piezoceramic components over a flat bar in its interior. The displacements of the cantilever were measured using an optical system tracking reflective targets distributed along the model. Additionally, the resulting reaction forces and the Leia mais…

High-silicon electrical steel powders aimed for additive manufacturing

Abstract: The Fe6.5Si soft magnetic alloy exhibits promising magnetic properties for energy applications, including nearzero magnetostriction, low magnetocrystalline anisotropy, and higher electrical resistivity than conventional electrical steels. However, its brittleness impedes industrial use. Recent advances in powder-based additive manufacturing show potential for processing high‑silicon electrical steels. This study focuses on Leia mais…

The effect of nanotube on the fracture toughness of alumina composite; a review

Abstract: For more than 40 decades, research has been widespread in the field of increasing the fracture toughness (KIc) of ceramic materials. Since carbon nanotubes (CNT) were announced in 1991, several studies have been published showing the potential of these nanomaterials in improving the fracture toughness of ceramic materials, mainly Leia mais…

INSCREVA-se em nossa newsletter

Receba nossas novidades em seu e-mail.

SUBSCRIBE to our newsletter

Receive our news in your email.

Pular para o conteúdo